HYDRO-EXTRACTOR GHE-120/GHE-150/GHE-180/GHE-200/GHE-220
TIANJIN GIANTEY MACHINERY CO., LTD. makes this machine for a long time and has rich experience in this field. The Working principle OF HYDRO-EXTRACTOR.The spin-drier is working on the principle of centrifugal motion. The inner cylinder will rotate at a very high speed driven by the motor, the water inside the clothes will leave the clothes in a centrifugal way at high speed, and then spines out of the cylinder, thus the water inside will be removed.
Internal cylinder material Stainless steel.
Structure of the machine: The frequency conversion off-center dehydrator has used the advanced sliding bearing part (1) the complete machine supporting in three sliding bearing place, and uses the elastic coupling, when dehydration, it can vibrate most greatly by the calcinate the alleviation function which maximum limit, not balanced causes because of the laying aside, causes the rotation to be steadier.
The enclosure and top cover are made of the steel plate and the bottom plate is iron- steel, the discharging tube is fitted under the bottom plate. The supporting stand and pedestal are all made of iron steel.
The main shaft is made of high-quality steel with two bearings. The bottom is supported with a thrust ball bearing to reduce abrasion and save energy.
Rotary cylinder is made of stainless steel plate with a buttonhole, the bottom of the cylinder is iron-steel with stainless steel bottom cover. The rotary cylinder is equipped on the cone face on the top of the main shaft to ensure stable rotation. The taper is 1:5.714.
Master control box: In the master control box is loaded with: The frequency conversion velocity modulation controller, cools the air blower, the transformer, the relay, the number obviously timer, electric control parts and so on indicating lamp, uses for to complete electrical machinery’s pro and con idling and the high-speed dehydration, as well as leads the cloth pro and con revolution.
HYDRO-EXTRACTOR used the feedback to apply the brake and to direct current applies the brake (popular name dynamic braking) its characteristic to exempt the replacement brake balloon trouble, reduced the breakdown which received as a result of the mechanical brake system, increased the machine service life.
The frequency changer working instruction is tight.
The frequency changer internal data non-this factory debugs the personnel not to revise if, from the revision, the consequence is proud friendly.
Services when the machine must shut off the buyer power source, must wait the frequency changer to demonstrate that the kneading board finishes attending when has nothing the demonstration, only then starts to overhaul, because the frequency changer was separating the power source instantaneous still to have the high pressure. (about 5 minutes)
When the dehydrator presents the vibration oversized should according to stop the button or on anxiously immediately the button box STOP the button. Causes the dehydrator to stop down, verifies the reason, after the trouble clearing, moves again, under record breakdown reason.
When the frequency changer presents the fail-safe, verifies the reason, after the trouble clearing, according to the master control box in the reset button, under the record breakdown reason.
Because other factors cause the frequency changer to do protect oneself, when has the alarm, the frequency changer will stop any output (i.e. not automatic brake condition) the electrical machinery (escaping water cylinder body) to revolve freely by the very big inertia, this time, by all means, must wait for the electrical machinery (to escape water cylinder body) to stop getting down, according to the breakdown demonstration code, looks up should the breakdown reason, after the trouble clearing, then moves.
Technical data：
| Type | GHE-120 | GHE-150 | GHE-180 | GHE-200 | GHE-220 |
| Internal cylinder size (inner diameter× height)（mm） | Φ1200*600 | Φ1500*660 | Φ1800*760 | Φ2000*860 | Φ2200*960 |
| Rotational speed of internal cylinder (r/min) | 750r/min | 750r/min | 500r/min | 480r/min | 450r/min |
| Main-shaft motor power(kW) | 7.5kw | 10kw | 15kw | 18kw | 22kw |
| Inverter power(kW) | 7.5kw | 11kw | 18.5kw | 22kw | 22kw |
| Voltage (V) | 380 | 380 | 380 | 380 | 380 |
| Max. Capacity (kg) | 300kg | 550kg | 900kg | 1200kg | 1500kg |
| Outline dimension (diameter × height) （mm） | Φ1700*2350 | Φ2000*2550 | Φ2400*2500*1650 | Φ2500*2600*1750 | Φ2600*2700*1850 |
| Net weight of complete machines (kg) | 2200kg | 2800kg | 3400kg | 4400kg | 5400kg |
| Total power | 7.5kw | 10kw | 15kw | 22kw | 22kw |
